e02b042.pdf

MINI -PROJECT

Audio Level Check

for Line Input

for the PC sound card

Design by T. Giesberts

This simple control circuit allows the level of an external stereo audio

source to be adapted to the sensitivity of, for example, a sound card. In

addition, an LED indicates if any signal levels are present that can cause

the input to be overdriven.

uations. A PC sound card, for exam-

ple, is generally not provided with a

level control. In addition, the maxi-

mum allowable input voltage of such

a card is limited by the 5-V power

supply of the chipset. This limits the

input to signals of less than 1 to 1.5

V, before clipping occurs.

The drawbacks that are caused in

practice by such fixed input sensi-

tivities and limited output signal lev-

els can be mitigated by preceding

the relevant line input with the con-

trol circuit that is described here.

The signal levels of 2 V that modern

CD- or DVD-players often provide

can be reduced to an acceptable

maximum. On the other hand, the

output level of 200 mV that older

equipment typically source, can be

amplified, something that will

improve the signal to noise ratio.

The adjustment range of our cir-

cuit amounts to no less than ±20

dB, so every conceivable signal

adaptation should be possible. In

order to avoid being unpleasantly

surprised by excessive signal levels,

an LED indicator has been added

which will indicate immediately

when the output signal exceeds a

certain (adjustable) value. Because

the current consumption is a mere

Standardisation is a long way off in many

areas. This is certainly true for audio signal

levels — a phenomenon that many of you will

have encountered at one time or another, usu-

ally at the most inopportune moment. With

equipment such as cassette decks, tuners,

CD/DVD-players, one can never be quite sure

what signal level to expect. Any-

thing is possible from around 200

mV to 2 V, or so.

If you wish to connect a signal

source to an input that does not have

a good input level adjustment, then

this can easily lead to unpleasant sit-

Elektor Electronics

11/2002

MINI -PROJECT

few mA, the level adapter can sim-

ply be powered from a 9-V battery;

that makes it pleasantly universally

deployable.

and an adjustable amplifier stage.

There is a single indicator common

to both channels. In order to power

the opamps symmetrically from a 9-

V battery, a virtual ground point has

been created with voltage divider

R27/R28/C11. Figure 1 shows the

complete schematic.

The indicator will be described

later, we will ﬁrst take a look at the

buffer and ampliﬁer stage.

The function of the input buffers

IC1c and IC1b is to provide a con-

stant load for the attached signal

source. The values are such that the

input impedance is ﬁxed at the well-

known standard value of 47 kΩ . The

opamps are connected as voltage fol-

lowers, while resistors R3 and R12

bias them to half of the power sup-

ply voltage. Because the circuit is powered

from an asymmetric power supply, a coupling

capacitor is present at the input. This capac-

itor is always charged by R1 and R10 to pre-

vent any unwanted sound effects when the

signal source is plugged in. The coupling

capacitor is followed by an additional protec-

tion network, guarding against high peak

voltages. This network consists of two diodes

and a resistor.

For practical reasons, an inverting topol-

ogy was purposely selected for the adjustable

ampliﬁer stages IC1a and IC1d. By using the

inverting inputs, the load on the potential

divider for the virtual ground (R27/R28) is

smaller, allowing higher resistance values

and consequently a lower total current con-

sumption.

If, for the moment, we limit the description

to the left channel only, we can establish that

Control circuit

If the circuit were only required to

attenuate, then we could have made

it easy for ourselves and a simple

passive voltage divider would have

sufficed. But in this case we also

wanted to amplify and, in addition,

we would also like a tidy circuit in

which the input and output-imped-

ance are not affected by the position

of the potentiometers.

That is why we decided to go for a

relatively ‘mature’ design. Each

channel consists of an input buffer

P1.A

4k7

+9V

47k

lin.

1N4148

IC1.C

47p

63V

100

IC1.A

4 µ 7

63V

1N4148

+9V

R26

R19

+9V

IC2.B

R21

47k

R27

R24

R23

BT1

IC2.A

220

25V

47 µ

25V

C12

C10

IC1

IC2

R25

D 6

220 µ

25V

100n

R28

C11

5V6

0W4

100 µ

10V

100k

IC2.D

R22

47k

R20

P1.B

R13

4k7

R14

4k7

IC2.C

+9V

47k

lin.

P2: 200mV... 1V(RMS)

R15

R16

1N4148

IC1.B

IC1 = TS924IN

IC2 = LM339

R11

47p

4 µ 7

63V

R17

100 Ω

IC1.D

R10

R12

4 µ 7

63V

R18

1N4148

020189 - 11

Figure 1. The level adapter actually consists of two separate circuits: the adjustment section and an overdrive indicator.

11/2002

Elektor Electronics

MINI -PROJECT

the maximum amplification of IC1a is equal

to (R5+P1)/R4 and the minimum is equal to

R5/(P1+R4). Because of small losses else-

where, this results in an adjustment range

from 10.5 to 0.09, which pretty much corre-

sponds to ±20 dB.

Resistor R6 (R15) was added to prevent

potential instability of the ampliﬁer as a result

of parasitic capacitance at the input of the

opamp in case the wiring to P1 is a little bit

long. Should the wiper of P1 be sporadically

intermittent, R7 (R16) ensures that there is

always negative feedback around the opamp

and the output will always be nicely at half

the power supply voltage. For stability rea-

sons, C2 (C5) limits the bandwidth to 60 kHz

at maximum ampliﬁcation.

Another two components to complete the

list: R8 (R17) ensures that the amplifier will

be unconditionally stable even with a capac-

itive load at the output (because of long output

cables, for example). R9 (R18) makes sure

that the output electrolytic capacitor is

always charged to prevent loud noises when

the output load is plugged in.

It is worth mentioning that for IC1 we

deliberately selected a rail-to-rail opamp, so

that despite the low power supply voltage,

reasonably high input voltages are still pos-

sible. The maximum is nominally more than

3V RMS , while with a nearly exhausted bat-

tery 2 V RMS is still not a problem.

OUT1

OUT2

R10

R18

020189-1

R11

R12

R21

R19

R27

IC1

IC2

C11

R20

R15

R23

R14

R22

C12

C10

Figure 2. The dimensions of the PCB make an extremely compact construction of

the level adapter possible.

COMPONENTS LIST

C7 = 47µF 25V radial

C8,C12 = 220µF 25V radial

C9,C10 = 100nF

C11 = 100µF 10V radial

Resistors:

R1,R10 = 270k

Indicator

The overdrive indicator is built around quad

comparator IC2. This IC is used to build a

window comparator for each channel. The

window comparator compares the output

signal of the adjustable ampliﬁer stage with

a variable reference. The outputs of IC2 are

of the open-collector type and can therefore

be simply connected together. If one of the

comparator input signals exceeds the refer-

ence voltage, adjusted with P2, LED D8 will

light up.

A few additional details regarding this cir-

cuit. The reference is set symmetrically

around half the power supply voltage with

the aid of R19, D5 and R20, so that both the

negative as well as the positive half of the

signal voltage is monitored. Because the

zener current is set to a really small value of

only 1 mA, the voltage drop across D5 is only

about 5.3 V. R21, R22, R23 and P2 are dimen-

sioned such that the reference voltage,

adjustable with P2, corresponds to signal

voltages from 200 mV to 1 V RMS .

As can be seen in the schematic, LED D6

(and series resistor R24) is connected in par-

allel with an electrolytic capacitor (C7). This

has been added to provide a certain amount of

Ω

R2,R6,R11,R15 = 1k Ω

R3,R12 = 56k

Semiconductors:

D1-D4 = 1N4148

D5 = zener diode 5.6V, 0.4W

D6 = LED, red, high-efficiency

IC1 = TS924IN ST (Farnell)

IC2 = LM339

Ω

R4,R5,R13,R14 = 4k Ω

R7,R16 = 1M

Ω

R8,R17,R26 = 100 Ω

R9,R18 = 100k

Ω

R19,R20 = 1k Ω 8

R21,R22,R27,R28 = 47k

Miscellaneous:

S1 = rocker switch, 1 make contact,

for chassis mounting

BT1 = 9 V battery with holder

Two 3.5 mm stereo jack sockets,

chassis mount

PCB, order code 020189-1 (see

Readers Service page). PCB layout

ﬁle also available from Free

Downloads at

www.elektor-electronics.co.uk

R23 = 10k Ω

R24 = 6k

R25 = 820 Ω

P1 = 47k

stereo potentiometer,

linear

P2 = 100 k mono potentiometer,

linear

Capacitors:

C1,C3,C4,C6 = 4µF7 63V radial

C2,C5 = 47pF

afterglow so that short duration sig-

nal peaks will become better visible.

R25 limits the maximum charging

current of C7 to a safe value for IC2.

Finally, R26 and C8 decouple the

power supply so that any potential

noise from the switching of the LED

has the least possible impact on the

ampliﬁers.

Construction

An extremely compact circuit board

has been designed for this circuit,

Elektor Electronics

11/2002

MINI -PROJECT

the layout and component overlay of

which is shown in Figure 2 . To

make sure that the adjustment and

indicator parts of the circuit don’t

‘bite’ each other, there is a deliberate

separation between the grounds of

both sub-circuits. The circuit board

is quite densely populated with

parts, so construction should not be

hurried.

The terminals for the inputs and

outputs are nicely grouped on one

side of the PCB, while on the oppo-

site side two SIL headers can be

found for the connections to P1 and

P2. These components have deliber-

ately not been fitted directly on the

PCB so that everyone can determine

for themselves what type of input

and output connectors (e.g. mini-

jack, cinch) and potentiometers to

use. In addition, this also affords

greater freedom in the selection of a

suitable enclosure.

The wiring between the input

and output connectors needs to be

done with shielded cable. Standard

hook-up wire can be used for the

potentiometers, but with the chan-

Some measurement results

an enclosure, both potentiometers can be pro-

vided with a scale to indicate the ampliﬁca-

tion and indicator signal level respectively.

The enclosure is preferably made from

metal, because this minimises possible dis-

turbances from any potential external noise

sources. The metal of the enclosure needs to

be connected to ground of the circuit. For

example, a suitable enclosure is type

Box1590N1 from the company H.O.D. How-

ever, the space inside this enclosure is just a

little too small to ﬁt the battery as well — in

this case the next larger size will have to be

used. For completeness’ sake, we will men-

tion that it was naturally the intention that D6

is mounted in such a way that it is visible

from the outside.

As already mentioned, the current con-

sumption of the circuit is so low (about 7 mA)

that a power supply consisting of a 9-V bat-

tery can suffice. However, if you will be using

the circuit in a more permanent application

than a mains adapter is certainly more appro-

priate. A good adapter with regulated output

is preferred. It is particularly important that

the no-load voltage of the adapter does not

exceed 12 V, because that is the maximum

operating voltage of IC1.

Input impedance

47 k Ω

Input voltage max.

(THD = 0.1%)

3.2 V RMS

Output voltage max.

(THD = 0.1%)

3.1 V RMS

THD+N (B=80 kHz) 200 mV in, 20 mV out

0.027 % (20 Hz - 20 kHz)

200 mV in, 200 mV out

0.005 % (20 Hz - 20 kHz)

200 mV in, 2 V out

0.002 % (20Hz - 1 kHz)

0.028 % (20 kHz)

THD+N (B=80kHz)

2 V in, 200 mV out

0.0026 % (20 Hz - 1 kHz)

0.007 % (20 kHz)

2 V in, 2 V out

0.002 % (20 Hz - 1 kHz)

0.01 %

(20 kHz)

Channel separation

> 66 dB (1 kHz)

> 42 dB (20 kHz)

Current consumption

LED off

6.7 mA

LED on

7.8 mA

nel separation in mind, it is best to

keep the wiring to P1 as short as is

possible. It is also recommended to

use a potentiometer with a metal

housing for this, the case of which is

connected to ground with a short

wire. Make sure that when wiring P1

and P2 that they are connected in

such a way that the level increases

when they are turned clockwise. The

numbers of the connections shown

on the schematic correspond with

those of the SIL headers on the PCB.

Once the circuit has been built into

(020189-1)

11/2002

Elektor Electronics

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: