FT3000 broszura.PDF
(
3532 KB
)
Pobierz
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd">
HF/50 MHz 100 W Transceiver
FT
DX
3000
/FX$SZTUBM3PPpOH'JMUFSTQSPWJEFVMUJNBUFXFBLTJHOBMSFDFJWFS
QFSGPSNBODFJODSPXEFETUSPOHTJHOBMFOWJSPONFOUT
e amazing Crystal Roong Filter performance
has been proven in the FT
DX
5000!
The Down conversion 9 MHz 1st IF frequency receiver construction, can realize
narrow 300 Hz (optional), 600 Hz and 3 kHz bandwidth roofing filters.
Implementing the extra sharp Crystal Roofing Filters provides superior close-in
dynamic range and affords the best receiver performance possible.
Large and wide color LCD display
The 3.5-inch wide color LCD displays the operating information and the status of
the transceiver functions, with high resolution (480 x 272 dots) on the screen.
The various FTDX3000 functions are displayed on this LCD and provide the
operator with easy to read operating information.
High Speed Spectrum Scope built-in
Although the FTDX3000 has only one receiver, a high speed Spectrum Scope is
built into the radio. When in the Auto Mode, the Spectrum Scope display is
updated in real time. The maximum bandwidth of the scope is 1 MHz, and the
minimum span width setting is 20 kHz. The best desired span is selectable for the
high resolution display. The current band activity can be monitored in real time.
AF SCOPE display and RTTY/PSK encoder/decoder
(optional)
Optional AF SCOPE and optional RTTY encoder/decoder functions have been
developed.
The wave form of the AF SCOPE signal can be displayed on the TFT LCD. Also,
the RTTY/PSK text may be displayed on the LCD.
CENTER: 9 MHz
SPAN: 20 kHz
300 Hz, 600 Hz, 3 kHz Crystal roofing Filters
Characteristics of the Crystal Roofing Filter (300 Hz)
Outstanding receiver performance
is the heritage of the FT
DX
5000
Independent Frequency display
The essential elements in receiver performance are the RF amplifier and the 1st mixer.
YAESU pursued the ultimate performance of these circuits. The RF amplifier has
optimized NF points, and the over-sized wide range RF transformer exhibits minimum
saturation in strong signal processing. The optimized devices were selected to
guarantee superior multi-signal RX performance. The desired maximum performance
has been realized in the development of the
FTDX3000 receiver circuitry. The FTDX3000
has the high dynamic range IP3 performance
that was realized and proven in the FTDX5000.
The Main operating frequency is the most important display in the radio, VFO-A
frequency is located just above the main dial. The newly developed LCD has a
wider viewing angle and higher contrast for convenient and effortless viewing.
Other features
14 MHz BAND CW (BW = 500 Hz)
IPO ON, Roofing FILTER = 600 Hz
2 kHz Spacing
• The specialized Receiver amplifier for 50 MHz is built in
• Three antenna connectors are provided.
The “ANT-3” terminal may be assigned to “RX-only”
• Signal output for an external receiver and the 9 MHz IF output are furnished
• High speed Automatic antenna tuner built in
• Optional μ-tune unit available
• USB interface equipped
-126 dBm
-20 dBm
IP3 : +33 dBm
DR : 106 dB
SIG
3rd IMD
Rear panel view
ANT INPUT [dBm]
RF amp with the large size
wide range transformer
The 1st mixer that provides
optimum reception performance
3rd Order Dynamic Range / IP3
IF DSP provides eective and optimized QRM rejection
The 32 bit high speed floating decimal DSP (max 2800 MIPS) provides effective
cancellation/reduction (DNR) of the random noise that is frequently frustrating in
the HF frequencies. Also: the AUTO NOTCH (DNF) that automatically eliminates
the dominant beat tone, the CONTOUR, and the APF, are very effective receiver
noise reduction tools in the HF bands operations. The YAESU original DSP QRM
and noise reduction functions are provided.
FTDX3000 Specifications
General
RX Frequency Range: 30 kHz - 56 MHz (operating)
1.8 MHz - 54 MHz (specified performance, Amateur bands only)
TX Frequency Ranges: 1.8 MHz - 54 MHz (Amateur bands only)
Frequency Stability: ±0.5 ppm (after 1 minute @+14 °F to +122 °F [–10 °C to +50 °C])
Operating Temperature Range: +14 °F to +122 °F (–10 °C to +50 °C)
Emission Modes: A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM),
F1B (RTTY), F1D (PACKET), F2D (PACKET)
Frequency Steps: 1/10 Hz (SSB, CW, & AM), 100 Hz (FM)
Antenna Impedance: 50 Ohms, unbalanced
16.7 - 150 Ohms, unbalanced (1.8 - 29.7 MHz)
25 - 100 Ohms, unbalanced (50 - 54 MHz)
(Tuner ON, 1.8 MHz - 50 MHz Amateur bands, TX only)
Power Consumption (Approx.): RX (no signal) 1.8 A
RX (signal present) 2.1 A
TX (100 W) 23 A
Supply Voltage: DC 13.8 V ± 10% (Negative Ground)
Dimensions (WxHxD): 14.4” x 4.5” x 12.3” (365 x 115 x 312 mm)
Weight (Approx.): 22.0 lbs (10 kg)
Transmitter
Power Output: 5 - 100 watts (2 - 25 watts AM carrier)
Modulation Types: J3E (SSB): Balanced,
A3E (AM): Low-Level (Early Stage),
F3E (FM): Variable Reactance
Maximum FM Deviation: ±5.0 kHz/ ±2.5 kHz
Harmonic Radiation: Better than -60 dB (1.8 MHz - 29.7 MHz Amateur bands: Harmonics)
Better than -50 dB (1.8 MHz - 29.7 MHz Amateur bands: Others)
Better than -65 dB (50 MHz Amateur band)
SSB Carrier Suppression: At least 60 dB below peak output
Undesired Sideband Suppression: At least 60 dB below peak output
3rd-order IMD: –31 dB @14 MHz 100 watts PEP
Bandwidth: 3 kHz (LSB/USB), 500 Hz (CW), 6 kHz (AM), 16 kHz (FM)
Audio Response (SSB): Not more than -6 dB from 300 to 2700 Hz
Microphone Impedance: 600 Ohms (200 to 10k Ohms)
Receiver
Circuit Type: Double-conversion Superheterodyne
Intermediate Frequencies: 9.000 MHz/ 30 kHz (24 kHz for AM/FM)
Sensitivity: SSB (BW: 2.4 kHz, 10 dB S+N/N)
4 µV (0.5 - 1.8 MHz) (IPO “ON”)
0.16 µV (1.8 - 30 MHz) (RF AMP 2 “ON”)
0.125 µV (50 - 54 MHz) (RF AMP 2 “ON”)
AM (BW: 6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz)
28 µV (0.5 - 1.8 MHz) (IPO “ON”)
2 µV (1.8 - 30 MHz) (RF AMP 2 “ON”)
1 µV (50 - 54 MHz) (RF AMP 2 “ON”)
FM (BW: 15 kHz, 12 dB SINAD)
0.5 µV (28 - 30 MHz) (RF AMP 2 “ON”)
0.35 µV (50 - 54 MHz) (RF AMP 2 “ON”)
There is no specification for frequency ranges not listed.
Selectivity (WIDTH: Center): Mode -6 dB -60 dB
CW/RTTY/PKT 0.5 kHz or better 750 Hz or less
SSB 2.4 kHz or better 3.6 kHz or less
AM 6 kHz or better 15 kHz or less
FM 15 kHz or better 25 kHz or less
Image Rejection: 70 dB or better (1.8 MHz - 30MHz Amateur bands)
60 dB or better (50 - 54MHz Amateur band)
Maximum Audio Output: 2.5 W into 4 Ohms with 10% THD
Audio Output Impedance: 4 to 8 Ohms (4 Ohms: nominal)
Conducted Radiation: Less than 4 nW
This device has not been approved by the FCC. This device may not be offered for sale or lease or be sold or leased until approval of the FCC has been obtained.
The information shown is preliminary and may be subject to change without notice or obligation.
YAESU MUSEN CO., LTD.
http://www.yaesu.com/jp
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002, Japan
YAESU USA
http://www.yaesu.com
US Headquarters
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
http://www.yaesu.co.uk
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
YAESU HK
http://www.yaesu.com.hk
Unit 1306-1308, 13F., Millennium City 2, 378 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong
2012.0503SS(USA/EXP/EU) B9200639 Printed in Japan
Plik z chomika:
sq4umm
Inne pliki z tego folderu:
OM Power 2000+.pdf
(3978 KB)
OPIS ANTENY LPDA.doc
(464 KB)
Maszt na korbe.pdf
(8677 KB)
Icom 7610 ins. PL.pdf
(2605 KB)
PDŁ 12-20.pdf
(2721 KB)
Inne foldery tego chomika:
AKCESORIA KF
Delta
Dokumentacje sprzętu radiowego
Elektronika Krótkofalarstwo(1)
Krótkofalarskie(1)
Zgłoś jeśli
naruszono regulamin