exj_13.pdf

(192 KB) Pobierz
XJ
FRAME AND BUMPERS
13 - 1
FRAME AND BUMPERS
TABLE OF CONTENTS
page
page
DESCRIPTION AND OPERATION
TABLE OF CONTENTS
page
DESCRIPTION AND OPERATION
DESCRIPTION AND OPERATION
BUMPERS
FRAME AND BUMPERS
DESCRIPTION
The bumpers on the Jeep Cherokee are made up of
the main bumper beam, the end caps, air deflector
(front bumper) and mounting brackets. Some Chero-
kee models also have a tow hook support bracket.
FRAME
DESCRIPTION
Jeep Cherokee vehicles do not have a conventional
frame. They are constructed as a unitized body and
frame. Jeep unibodies are constructed from special
high strength steel and coated metals. This process
reduces weight and provides strength to withstand
the forces applied against structural members. The
structural members provide a unibody that has great
structural strength.
OPERATION
The bumpers are fastened to the unitized body
frame rails. The bumper end caps are fastened to the
bumper and the body side sheet metal.
886890577.008.png
13 - 2
FRAME AND BUMPERS
XJ
BUMPERS
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
(4) Lifting the end cap from the bottom, tilt
slightly upward and slide it outward to disengage the
retainer tab from the bumper (Fig. 2).
(5) Separate the end cap from the bumper.
FRONT BUMPER END CAP
REMOVAL
(1) Remove the rivet attaching the end cap to the
air deflector.
(2) Remove the bolts and nuts attaching the end
cap to the bumper (Fig. 1).
(3) Pull back the wheelhouse liner and remove the
screws attaching the end cap to the front fender.
INSTALLATION
(1) Position the end cap on the bumper and engage
the retaining tab.
(2) Install the screws attaching the end cap to the
front fender.
(3) Install the bolts attaching the end cap to the
bumper. Tighten the nut to 9 N·m (7 ft. lbs.) torque.
Fig. 1 Front Bumper
1 – U-NUT
2 – TOW HOOK SUPPORT BRACKET
3 – END CAP
4 – RIVET
5 – AIR DEFLECTOR
6 – MOUNTING BRACKET
7 – BUMPER
886890577.009.png 886890577.010.png
XJ
FRAME AND BUMPERS
13 - 3
REMOVAL AND INSTALLATION (Continued)
Fig. 2 Bumper End Cap
1 – RETAINER TAB
2 – BUMPER END CAP
3 – BUMPER
4 – GRILLE
Fig. 3 Vacuum Reservoir
1 – VACUUM LINE
2 – RESERVOIR SCREWS
3 – VACUUM RESERVOIR
(4) Install the rivet attaching the end cap to air
deflector.
FRONT BUMPER
(3) If necessary, remove bolt attaching tow hook
reinforcement to frame.
REMOVAL
(1) Remove bumper end caps.
(2) If equipped, disengage fog lamp wire harness
connectors.
(3) Disconnect vacuum line from reservoir (Fig. 3).
(4) Remove Torx-head bolts that attach bumper to
mounting brackets (Fig. 1).
(5) Remove bumper from vehicle.
(6) If
necessary,
remove
bolts
attaching
bumper
mounting brackets to frame.
INSTALLATION
(1) If removed, install bolts attaching bumper
mounting brackets to frame. Tighten bolts to 55 N·m
(41 ft. lbs.) torque.
(2) Position bumper on front of vehicle.
(3) Install Torx-head bolts that attach bumper to
mounting brackets. Tighten bolts to 55 N·m (41 ft.
lbs.) torque.
(4) Connect vacuum line to reservoir.
(5) If equipped, engage fog lamp wire harness con-
nectors.
(6) Install bumper end caps.
Fig. 4 Front Tow Hook
1 – MOUNTING BRACKET
2 – TOW HOOK
3 – TOW HOOK REINFORCEMENT
INSTALLATION
(1) If removed, install bolt attaching tow hook
reinforcement to frame. Tighten bolt to 30 N·m (22 ft.
lbs.) torque.
(2) Position tow hook on reinforcement.
(3) Install bolts attaching tow hook to tow hook
reinforcement. Tighten bolts to 100 N·m (74 ft. lbs.)
torque.
FRONT TOW HOOK
REMOVAL
(1) Remove bolts attaching tow hook to tow hook
reinforcement (Fig. 4).
(2) Separate tow hook from reinforcement.
886890577.011.png 886890577.001.png 886890577.002.png 886890577.003.png
13 - 4
FRAME AND BUMPERS
XJ
REMOVAL AND INSTALLATION (Continued)
REAR BUMPER END CAP
refer to removal procedure within Group 13, Frame
and Bumpers.
(2) Remove bumper end caps.
(3) Remove
REMOVAL
(1) Remove the screws attaching the bumper end
cap to the quarter panel and the bumper (Fig. 5).
(2) Lift the end cap slightly upward and slide it
rearward to release it from the retainer.
(3) Separate the end cap from the vehicle.
upper
nuts
that
attach
bumper
to
bumper support brackets (Fig. 5).
(4) Remove
lower
bolts
that
attach
bumper
to
bumper support brackets.
(5) Remove bumper from vehicle.
(6) If necessary, remove bumper support brackets
from the rear sill.
INSTALLATION
(1) Position the end cap on the rear of the retainer
and the outer edge of the bumper.
(2) Slide the end cap forward onto the retainer.
Ensure
INSTALLATION
(1) If removed, install bumper support brackets on
the rear sill. Tighten bolts to 55 N·m (41 ft. lbs.)
torque.
(2) Position bumper on support brackets.
(3) Install bolts that attach bumper to bumper
support brackets. Tighten nuts to 55 N·m (41 ft. lbs.)
torque.
(4) Install bumper end caps.
(5) If removed, install trailer hitch.
the
end
cap
overlaps
the
lip
of
the
rear
wheelhouse liner.
(3) Install the screw attaching the front of the end
cap
to
the
underside
of
the
quarter
panel
and
bumper.
REAR BUMPER
REMOVAL
(1) For vehicles equipped with a trailer hitch,
remove hitch before removing bumper. If necessary,
Fig. 5 REAR BUMPER END CAP
1 – SPLASH SHIELD
2 – REAR SILL
3 – BRACKET
4 – STUD
5 – RIVET
6 – RETAINER
7 – END CAP
8 – PLASTIC BLIND RIVET
9 – BUMPER
886890577.004.png 886890577.005.png
XJ
FRAME AND BUMPERS
13 - 5
REMOVAL AND INSTALLATION (Continued)
REAR TOW HOOK
REMOVAL
(1) Remove bolts that attach tow hook bracket and
tow hook to frame rail (Fig. 6).
(2) Remove bracket and tow hook from frame rail.
INSTALLATION
(1) Position bracket and tow hook on frame rail.
(2) Install bolts that attach tow hook bracket and
tow hook to frame rail. Tighten bolts to 94 N·m (70
ft. lbs.) torque.
Fig. 6 Rear Tow Hook
1 – WELD NUT
2 – FRAME REINFORCEMENT BRACKET
3 – RIVET
4 – SUPPORT BRACKET
5 – BOLT
6 – TOW HOOK
7 – BOLT
8 – BOLT
9 – FRAME RAIL
886890577.006.png 886890577.007.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin