get_Graph_e.pdf

(341 KB) Pobierz
Table of Contents
SIMATIC HMI
Introduction
Configuring Graphics
Displays
Commissioning Operating Units
Basic Steps for a Configuration
Product Brief
Extend Configuration with
Simple Elements
Edition 12/01
A5E00148106
921873814.030.png 921873814.031.png 921873814.032.png 921873814.033.png 921873814.001.png 921873814.002.png 921873814.003.png 921873814.004.png 921873814.005.png
Safety Guidelines
This manual contains notices which you should observe to ensure your
own personal safety, as well as to protect the product and connected
equipment. These notices are marked as follows according to the level
of danger:
Danger
indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Warning
indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Caution
used with the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in minor or moderate injury.
Caution
used without safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
Attention
indicates that unwanted events or status can occur if the relevant
information is not observed.
Note
draws your attention to particularly important information on the product,
handling the product, or to a particular part of the documentation.
Qualified Personnel
Equipment may be commissioned and operated only by qualified
personnel. Qualified personnel within the meaning of the safety notices
in this manual are persons who are authorized to commission, ground
and identify equipment, systems and circuits in accordance with safety
engeneering standards.
921873814.006.png 921873814.007.png 921873814.008.png 921873814.009.png 921873814.010.png 921873814.011.png 921873814.012.png 921873814.013.png 921873814.014.png 921873814.015.png 921873814.016.png 921873814.017.png 921873814.018.png 921873814.019.png
 
Correct Usage
Note the following:
Warning
The equipment may be used only for the applications stipulated in the
catalog and in the technical description and only in conjunction with
other equipment and components recommended or approved by
Siemens.
Startup must not take place until it is established that the machine,
which is to accommodate this component, is in conformity with the
guideline 98/37 ECC.
Faultless and safe operation of the product presupposes proper
transportation, proper storage, erection and installation as well as
careful operation and maintenance.
Trademarks
The registered trademarks of the Siemens AG can be found in the
preface. The remaining trademarks in this publication may be
trademarks, whose use by third parties for their own purposes could
violate the rights of the owner.
Impressum
Editor and Publisher: A&D PT1 D1
Copyright Siemens AG 2001 All rights reserved
Exclusion of liability
The transmission and reproduction of this documentation and the
exploitation and communication of its contents are not allowed,
unless expressly granted. Violators are liable for damages. All rights
reserved, especially in the case of the granting of a patent or
registration by GM.
We have checked the content of this publication for compliance with
the described hard and software. However, discrepancies cannot be
excluded, with the result that we assume no guarantee for total
compliance. The information in this publication is checked regularly,
and any necessary corrections are included in the following editions.
We would be grateful for any suggestions for improvement.
Siemens AG
Bereich Automation & Drives
Geschftsgebiet SIMATIC HMI
Postfach 4848, D-90327 Nuernberg
Siemens AG 2001
Technical data subject to change.
Siemens Aktiengesellschaft
Order number A5E00148106
921873814.020.png 921873814.021.png 921873814.022.png 921873814.023.png
 
Configuring Graphics Displays
Contents
Contents
Page
Introduction ............................................................. 3
Commissioning Operating Units ............................. 7
Basic Steps for a Configuration .............................. 9
Extend Configuration with Simple Elements ......... 21
SIMATIC
is a registered trademark of Siemens AG.
The other designations in this document may be trademarks which, when
used by others for their own purposes, may constitute a violation of the
ownersÓ rights.
Siemens AG
1
921873814.024.png 921873814.025.png 921873814.026.png 921873814.027.png 921873814.028.png 921873814.029.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin