1185.PDF
(
279 KB
)
Pobierz
19-0045; Rev 1; 5/94
Triple-Output Power-Supply Controller
for Notebook Computers
_______________General Description
The MAX783 is a system-engineered power-supply controller
for notebook computers or similar battery-powered equipment.
It provides two high-performance step-down (buck) pulse-
width modulators (PWMs) for +3.3V/+5V and dual PCMCIA
VPP outputs powered by an integral flyback winding controller.
Other functions include dual, low-dropout, micropower linear
regulators for CMOS/RTC back up, and two precision low-
battery-detection comparators.
High efficiency (95% at 2A, greater than 80% at loads from
5mA to 3A) is achieved through synchronous rectification
and PWM operation at heavy loads, and Idle-Mode
TM
oper-
ation at light loads. The MAX783 uses physically small
components, thanks to high operating frequencies
(300kHz/200kHz) and a new current-mode PWM architec-
ture that allows for output filter capacitors as small as 30µF
per ampere of load. Line- and load-transient responses
are terrific, with a high 60kHz unity-gain crossover frequen-
cy that allows output transients to be corrected within four
or five clock cycles. Low system cost is achieved through
a high level of integration and the use of low-cost external
N-channel MOSFETs. The integral flyback winding con-
troller provides a low-cost, +15V high-side output that regu-
lates even in the absence of a load on the main output.
Other features include low-noise, fixed-frequency PWM
operation at moderate to heavy loads and a synchronizable
oscillator for noise-sensitive applications such as electro-
magnetic pen-based systems and communicating comput-
ers. The MAX783 is similar to the MAX782, except the fly-
back winding is on the 3.3V inductor instead of the 5V
inductor, the VPP outputs can be optionally programmed to
3.3V, and the device may be completely shut down.
________________________Applications
Notebook Computers
Portable Data Terminals
Communicating Computers
Pen-Entry Systems
____________________________Features
©
Dual PWM Buck Controllers (+3.3V and +5V)
©
Dual PCMCIA VPP Outputs (0V/3.3V/5V/12V)
©
Two Precision Comparators or Level Translators
©
Power-Ready Status Output (
)
©
95% Efficiency
©
Optimized for 6-Cell Applications
©
420µA Quiescent Current;
70µA in Standby (linear regulators alive)
25µA Shutdown Current
©
5.5V to 30V Input Range
©
Small SSOP Package
©
Fixed Output Voltages Available:
3.3V (standard)
3.45V (High-Speed Pentium
™
)
3.6V (PowerPC
™
)
______________Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
V
OUT
MAX783CBX
0°C to +70°C
36 SSOP
3.3V
MAX783RCBX
0°C to +70°C
36 SSOP
3.45V
Ordering Information continued on last page.
__________________Pin Configuration
TOP VIEW
ON3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
36
35
34
33
32
31
30
29
28
27
26
25
24
23
SS3
CS3
FB3
DH3
LX3
BST3
SHDN
D1
D2
VH
Q2
MAX783
Q1
DL3
V+
VL
FB5
PGND
DL5
BST5
RDY5
VPPA
_______Typical Application Diagram
VDD
VPPB
+3.3V
GND
P
MEMORY
PERIPHERALS
m
5.5V
TO
30V
POWER
SECTION
REF
+5V
MAX783
SYNC
LX5
4
VPP
CONTROL
ON3
ON5
SYNC
DA1
22
21
20
19
15
16
17
18
DH5
CS5
SS5
SUSPEND POWER
DA0
LOW-BATTERY WARNING
DB1
DUAL
PCMCIA
SLOTS
DB0
ON5
VPP (0V/3.3V/5V/12
V)
SHDN
VPP (0V/3.3V/5V/12V)
SSOP
™
Idle-Mode is a trademark of Maxim Integrated Products. Pentium is a trademark of Intel. PowerPC is a trademark of IBM.
________________________________________________________________ Maxim Integrated Products
1
Call toll free 1-800-998-8800 for free samples or literature.
Triple-Output Power-Supply Controller
for Notebook Computers
ABSOLUTE MAXIMUM RATINGS
V+ to GND .................................................................-0.3V, +36V
PGND to GND........................................................................±2V
VL to GND ...................................................................-0.3V, +7V
BST3, BST5 to GND ..................................................-0.3V, +36V
LX3 to BST3.................................................................-7V, +0.3V
LX5 to BST5.................................................................-7V, +0.3V
Inputs/Outputs to GND
(D1, D2, S
—
H
—
D
—
–
, ON5, REF, SYNC, DA1, DA0, DB1, DB0, ON5,
SS5, CS5, FB5, R
—
D
—
Y
—–
, CS3, FB3, SS3, ON3).-0.3V, (VL + 0.3V)
VDD to GND.................................................................-0.3V, 20V
VPPA, VPPB to GND.....................................-0.3V, (VDD + 0.3V)
VH to GND ...................................................................-0.3V, 20V
Q1, Q2 to GND................................................-0.3V, (VH + 0.3V)
DL3, DL5 to PGND..........................................-0.3V , (VL + 0.3V)
DH3 to LX3 ..................................................-0.3V, (BST3 + 0.3V)
DH5 to LX5 ..................................................-0.3V, (BST5 + 0.3V)
REF, VL, VPP Short to GND........................................Momentary
REF Current.........................................................................20mA
VL Current ...........................................................................50mA
VPPA, VPPB Current .........................................................100mA
Continuous Power Dissipation (T
A
= +70°C)
SSOP (derate 11.76mW/°C above +70°C) ...................762mW
Operating Temperature Ranges:
MAX783CBX/MAX783_CBX.................................0°C to +70°C
MAX783EBX/MAX783_EBX ..............................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = 15V, GND = PGND = 0V, I
VL
= I
REF
= 0mA, S
—
H
—
D
—
N
–
= ON3 = ON5 = 5V, other digital input levels are 0V or +5V,
T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
3.3V AND 5V STEP-DOWN CONTROLLERS
Input Supply Range
5.5
30
V
0mV < (CS5-FB5) < 70mV, 6V < V + < 30V
(includes load and line regulation)
FB5 Output Voltage
4.80
5.08
5.20
V
MAX783
MAX783R
MAX783S
3.17
3.35
3.46
0mV < (CS3-FB3) < 70mV, 6V < V + < 30V
(includes load and line regulation)
FB3 Output Voltage
3.32
3.50
3.60
V
3.46
3.65
3.75
Load Regulation
Either controller (0mV to 70mV)
Either controller (6V to 30V)
2.5
%
Line Regulation
0.03
%/V
CS3-FB3 or CS5-FB5
80
100
120
Current-Limit Voltage
mV
CS3-FB3 (VDD < 13V, flyback mode)
-50
-100
-160
SS3/SS5 Source Current
2.5
4.0
6.5
µA
SS3/SS5 Fault Sink Current
2
mA
15V FLYBACK CONTROLLER
VDD Regulation Setpoint
Falling edge, hysteresis = 1%
13
14
V
VDD Shunt Setpoint
Rising edge, hysteresis = 1%
18
20
V
VDD Shunt Current
VDD = 20V
2
3
mA
VDD = 18V, ON3 = ON5 = 5V, VPPA/VPPB programmed to
12V with no external load
Quiescent VDD Current
140
300
µA
VDD = 18V, ON3 = ON5 = 5V, VPPA/VPPB programmed to
0V
Off VDD Current
15
30
µA
PCMCIA REGULATORS (Note 1)
Program to 12V, 13V < VDD < 19V, 0mA < I
L
< 60mA
11.60
12.10
12.50
Program to 5V, 13V < VDD < 19V, 0mA < I
L
< 60mA
4.85
5.05
5.20
VPPA/VPPB Output Voltage
V
Program to 3.3V, 13V < VDD < 19V, 0mA < I
L
< 60mA
3.17
3.30
3.43
Program to 0V, 13V < VDD < 19V, 0mA < I
L
< 0.3mA
-0.30
0.30
2
_______________________________________________________________________________________
Triple-Output Power-Supply Controller
for Notebook Computers
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 15V, GND = PGND = 0V, I
VL
= I
REF
= 0mA, S
—
H
—
D
—
N
–
= ON3 = ON5 = 5V, other digital input levels are 0V or +5V,
T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
INTERNAL REGULATOR AND REFERENCE
VL Output Voltage
ON5 = ON3 = 0V, 5.5V < V+ < 30V, 0mA < I
L
< 25mA
4.5
5.5
V
VL Fault Lockout Voltage
Falling edge, hysteresis = 1%
3.6
4.2
V
VL/FB5 Switchover Voltage
(also R
—
D
—
Y
—–
Trip Voltage)
Rising edge of FB5, hysteresis = 1%
4.2
4.7
V
REF Output Voltage
No external load (Note 2)
3.24
3.36
V
REF Fault Lockout Voltage
Falling edge
2.4
3.2
V
REF Load Regulation
0mA < I
L
< 5mA (Note 3)
30
75
mV
S
—
H
—
D
—
–
= D1 = D2 = ON3 = ON5 = DA0 = DA1 = DB0 =
DB1 = 0V, V+ = 30V
D1 = D2 = ON3 = ON5 = DA0 = DA1 = DB0 = DB1 = 0V,
V+ = 30V
Shutdown V+ Current
25
40
µA
Standby V+ Current
70
110
µA
Quiescent Power Consumption
(both controllers on)
D1 = D2 = D3 = DA0 = DA1 = DB0 = DB1 = 0V,
FB5 = CS5 = 5.25V, FB3 = CS3 = 3.5V
FB5 = CS5 = 5.25V, VL switched over to FB5
5.2
8.6
mW
Off V+ Current
30
60
µA
COMPARATORS
D1, D2 Trip Voltage
Falling edge, hysteresis = 1%
1.61
1.69
V
D1, D2 Input Current
D1 = D2 = 0V to 5V
VH = 15V, V
OUT
= 2.5V
VH = 15V, V
OUT
2.5V
I
SOURCE
= 5µA, VH = 3V
±100
nA
Q1, Q2 R
—
D
—
Y
—–
Source Current
12
20
30
µA
Q1, Q2 R
—
D
—
Y
—–
Sink Current
200
500
1000
µA
Q1, Q2, R
—
D
—
Y
—–
Output High Voltage
VH - 0.5
V
Q1, Q2, R
—
D
—
Y
—–
Output Low Voltage
I
SINK
= 20µA, VH = 3V
VH = 18V, D1 = D2 = 5V, no external load
0.4
V
Quiescent VH Current
4
10
µA
OSCILLATOR AND INPUTS/OUTPUTS
SYNC = 3.3V
SYNC = 0V or 5V
270
300
330
Oscillator Frequency
kHz
170
200
230
SYNC High Pulse Width
200
ns
SYNC Low Pulse Width
200
ns
SYNC Rise/Fall Time
Not tested
200
ns
Oscillator SYNC Range
240
350
kHz
SYNC = 3.3V
89
92
Maximum Duty Cycle
%
SYNC = 0V or 5V
92
95
S
—
H
—
D
—
–
, ON3, ON5, DA0, DA1, DB0, DB1, SYNC
Input Low Voltage
0.8
V
S
—
H
—
D
—
–
, ON3, ON5, DA0, DA1, DB0, DB1
2.4
Input High Voltage
V
SYNC
VL - 0.5
S
—
H
—
D
—
–
, ON3, ON5, DA0, DA1, DB0, DB1, V
IN
= 0V or 5V
Input Current
±1
µA
_______________________________________________________________________________________
3
Triple-Output Power-Supply Controller
for Notebook Computers
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 15V, GND = PGND = 0V, I
VL
= I
REF
= 0mA, S
—
H
—
D
—
N
–
= ON3 = ON5 = 5V, other digital input levels are 0V or +5V,
T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DL3/DL5 Sink/Source Current
V
OUT
= 2V
1
A
DH3/DH5 Sink/Source Current
BST3-LX3 = BST5-LX5 = 4.5V, V
OUT
= 2V
1
A
DL3/DL5 On-Resistance
High or low
7
½
DH3/DH5 On-Resistance
High or low, BST3-LX3 = BST5-LX5 = 4.5V
7
½
Note 1:
Output current is further limited by maximum allowable package power dissipation.
Note 2:
Because the reference uses VL as its supply, the REF line regulation error is insignificant.
Note 3:
The main switching outputs track the reference voltage. Loading the reference reduces the main outputs slightly according
to the closed-loop gain (AV
CL
) and the reference voltage load regulation error. AV
CL
for the +3.3V supply is unity gain.
AV
CL
for the +5V supply is 1.54.
__________________________________________Typical Operating Characteristics
(Circuit of Figure 1, Transpower TTI5902 transformer, T
A
= +25°C, unless otherwise noted.)
EFFICIENCY vs.
+5V OUTPUT CURRENT
EFFICIENCY vs.
+3.3V OUTPUT CURRENT
MAXIMUM +15V VDD OUTPUT CURRENT vs.
SUPPLY VOLTAGE
100
100
500
V+ = 6V
V+ = 6V
VDD
>
+13V
+3.3V REGULATING
90
90
400
V+ = 15V
V+ = 15V
+3.3V LOAD = 0A
80
80
300
+3.3V LOAD = 3A
70
70
200
N1-N4 = IRF7101
ON3 = LOW
F = 200kHz
N1-N4 = IRF7101
ON3 = ON5 = HIGH
F = 200kHz
60
60
100
50
1m
50
1m
0
10m
100m
1
10
10m
100m
1
10
0
5
10
15
20
+5V OUTPUT CURRENT (A)
+3.3V OUTPUT CURRENT (A)
SUPPLY VOLTAGE (V)
QUIESCENT SUPPLY CURRENT vs.
SUPPLY VOLTAGE
STANDBY SUPPLY CURRENT vs.
SUPPLY VOLTAGE
14
2.5
2.0
13
ON3 = ON5 = HIGH
1.5
2
ON3 = ON5 = 0V
1.0
1
0.5
0
0
0
6
12
18
24
30
0
6
12
18
24
30
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
4
_______________________________________________________________________________________
Triple-Output Power-Supply Controller
for Notebook Computers
____________________________Typical Operating Characteristics (continued)
(Circuit of Figure 1, Transpower TTI5902 transformer, T
A
= +25°C, unless otherwise noted.)
MINIMUM V
IN
TO V
OUT
DIFFERENTIAL
vs. +5V OUTPUT CURRENT
SWITCHING FREQUENCY vs.
LOAD CURRENT
SHUTDOWN SUPPLY CURRENT vs.
SUPPLY VOLTAGE
1000
500
1.0
SYNC = REF (300kHz)
ON3 = ON5 = HIGH
400
0.8
100
300kHz
+5V, V
IN
= 7.5V
300
0.6
10
SHDN = 0V
+5V, V
IN
= 30V
200
0.4
200kHz
+3.3V, V
IN
= 7.5V
1
+5V OUTPUT
STILL REGULATING
100
0.2
0.1
100
m
0
0
1m
10m
100m
1
0
1m
10m
100m
1
10
6
12
18
24
30
LOAD CURRENT (A)
SUPPLY VOLTAGE (V)
+5V OUTPUT CURRENT (A)
IDLE-MODE WAVEFORMS
PULSE-WIDTH MODULATION MODE WAVEFORMS
+5V OUTPUT
50mV/div
LX VOLTAGE
10V/div
2V/div
+5V OUTPUT
VOLTAGE
50mV/div
500ns/div
200
m
s/div
I
LOAD
= 100mA
V
IN
= 10V
I
LOAD
= 1A
V
IN
= 16V
_______________________________________________________________________________________
5
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin