FS527_A0HR-9550-02E.pdf
(
1808 KB
)
Pobierz
FS-527
Finisher
II. Confirmation before installation
1. To move the finisher, be sure to push it in the
directions of the arrows as shown in the illustra-
tion. (Precaution against falling of the finisher).
INSTALLATION MANUAL
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
Applied Machines: C652/C552/C452/C652DS/C552DS
COLOR MFP: 65 ppm/55 ppm/45 ppm
Product Code: A0P0/A0P1/A0P2/A1DM/A1DN
Caution:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take a
good position of not being excessively loaded.
(mass: approx. 42 kg (95-9/16 lb))
No.
Name
Shape
Q’ty
Note:
• This manual provides the illustrations of the
accessory parts and machine that may be
slightly different in shape from yours. In that
case, instead of the illustrations, use the
appearance of your machine to follow the
installation procedure. This does not cause any
significant change or problem with the proce-
dure.
• When installing the finisher in the C652/C552/
C652DS/C552DS, you need the rails, the
mounting plates, and the screws (4 × 6 mm)
that are supplied with the machine.
7.
Mounting
bracket E*
1
A0HRIXC007DA
8.
Exit tray
A0HRIXC012DA
I. Accessory parts
2. Parts are arranged in a box as shown in the illus-
tration.
1
No.
Name
Shape
Q’ty
Parts for C652/C552/C452/C652DS/C552DS
Common parts
1.
Finisher
A0HRIXC008DA
9.
Guide plate A
Rail (right)
Rail (left)
1
1
A0HRIXC009DA
10.
Guide plate B
A1DMIXC009DA
A1DMIXC010DA
Mounting plate (right)
Mounting plate (left)
A0HRIXC001DA
1
Parts for C360/C280/C220
2.
Horizontal
transport unit
A0HRIXC046DB
1
3. Choose a horizontal and stable floor for installing
the machine.
4. The packaging material should not be reused for
repacking.
5. When installing the optional punch kit, saddle
stitcher, and separator (JS-603), install the punch
kit, saddle stitcher, and separator (JS-603) first
and then install the finisher.
A0HRIXC010DA
11.
Mounting screw
A1DMIXC011DA
A1DMIXC012DA
1
A0HRIXC002DA
3.
Mounting
bracket A
A0HRIXC011DA
12.
Screw A
(3 × 8 mm)
1
4
9646
13.
Screw B*
(3 × 16 mm)
A0HRIXC003DA
4.
Mounting
bracket B
4
1
9J08IXC075DA
14.
Screw C*
(4 × 8 mm)
1
A0HRIXC004DA
9735
5.
Mounting
bracket C*
15.
Screw D
(4 × 8 mm)
2
1
4038IXC033DA
16.
Installation
manual
A0HRIXC005DA
6.
Mounting
bracket D*
1
set
1
4980IXC019DA
* This part is not used with the finisher.
A0HRIXC006DA
A0HR-9550-02
E-1
III. Installation procedures
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove the user’s guide holder from the
machine.
6. Remove the protective tapes of the horizontal
transport unit.
9. Attach the furnished guide plate B to the horizon-
tal transport unit (two screws).
Note:
Use the screws removed in step 7.
12. Only when installing the finisher in the C652/
C552/C652DS/C552DS, perform the following
steps (1) to (4).
* When installing the finisher in the C452, follow
the instructions of the steps 13 and later.
(1) Place the rail (left), aligning its dowel with the
hole on the machine.
A0HRIXC015DA
7. Remove the guide plate from the horizontal trans-
port unit (two screws).
A0HRIXC021DA
A07UIXC004DA
10. Turn the horizontal transport unit upside down.
Disengage the three tabs and remove the
spacer as shown in the illustration.
3. Remove the cover from the lower portion on the
left side of the machine as shown in the
illustration.
A0HRIXC049DA
(2) Install the mounting plate (left) as shown in the
illustration (three screws supplied with the
machine).
A0HRIXC019DA
8. Attach the furnished guide plate A to the horizon-
tal transport unit by inserting the two tabs into the
holes.
A0HRIXC044DA
A0HRIXC048DA
11. Remove the spacer as shown in the illustration
(three screws).
4. Remove the guide from the exit section of the
machine.
A0HRIXC050DA
(3) Place the rail (right), aligning its dowel with the
hole on the machine.
A0HRIXC020DA
A0HRIXC045DA
A01GIXC082DA
5. Remove the output tray (OT-503) if it is mounted
on the machine.
Note:
For the removal procedure, see the installation
manual for the output tray (OT-503).
A0HRIXC051DA
E-2
(4) Install the mounting plate (right) as shown in
the illustration (three screws supplied with the
machine).
15. Remove the locking tapes and the locking pro-
tection materials from the finisher.
17. Connect the two horizontal transport unit con-
nectors to the connectors located at the rear of
the right side of the finisher. Secure the cord with
a cord clamp.
20. Push the lever pulled in step 18 back to its origi-
nal position. Align the mounting hole on the lever
with the screw hole on the finisher, and then
screw the lever to the finisher (one furnished
mounting screw).
Note:
The mounting hole on the lever must overlap with
the screw hole on the finisher.
Screw hole
A0HRIXC024DB
A0HRIXC052DA
A0HRIXC028DA
13. Attach the furnished mounting plates A (left) and
B (right) to the upper left side of the main body
(two furnished screw A’s each).
18. Open the finisher front door and pull the lever.
Mounting hole
on the lever
A0HRIXC031DA
*
If the mounting hole on the lever does not overlap
with the screw hole on the finisher, take the fol-
lowing steps (1) to (9).
(1) Disconnect the two connectors and remove the
cord clamp. Remove the finisher from the main
body.
A0HRIXC025DB
A0HRIXC029DA
A0HRIXC016DA
19. Install the finisher on the machine.
14. Mount the hospital transport unit to the machine
(two screw D’s furnished with the finisher).
A0HRIXC026DB
A0HRIXC040DA
16. Rotate the handle to move the stapler unit
toward you and remove the lock tape.
(2) Remove the lower front cover from the finisher
(two screws).
A0HRIXC047DA
A0HRIXC041DA
Handle
A0HRIXC027DA
A0HRIXC032DA
E-3
(3) Remove the cover from the caster located on
the front side of the finisher (one screw).
(6) Adjust the height of the four casters to align the
mark on the lever with the screw hole on the
finisher.
21. Insert exit tray into the sub tray paper exit slot on
the finisher.
A0HRIXC033DA
A0HRIXC037DA
A0HRIXC036DA
(4) Remove the rear cover from the finisher (ten
screws).
22. Connect the hookup cord of the horizontal trans-
port unit to the machine.
Screw hole
Mark
A0HRIXC043DA
(7) To install the covers and other parts removed
in step (2) to (5), reverse the removal proce-
dure.
(8) Connect the two connectors removed in step
(1) and secure the cord with a cord clamp.
(9) Install the finisher on the machine.
A0HRIXC034DA
A11PIXC018DB
(5) Remove the cover from the caster located on
the rear side of the finisher (one screw).
23. Reinstall the user’s guide holder which has been
removed in step 2, to the position shown.
A0HRIXC035DA
A0HRIXC042DA
E-4
Plik z chomika:
ramirez_pl
Inne pliki z tego folderu:
au-101_im_A09M-9557-00E.pdf
(362 KB)
au-102_im_A0X9-9557-00E.pdf
(359 KB)
au-201_im_A09N-9557-00E.pdf
(431 KB)
bizhub_c360_c280_c220_im_A0ED-9602-11E.pdf
(1623 KB)
df-617_im_A0HU-9560-00E.pdf
(581 KB)
Inne foldery tego chomika:
firmware c280
User Guides
Zgłoś jeśli
naruszono regulamin